AT8200-2000-0100 | NCT electronics, with housing, without mover, basic electronics, suitable for third-party movers
AT8200-2000-0100 | NCT electronics, with housing, without mover, basic electronics, suitable for third-party movers
The NCT electronics form the basis for an application-specific adaptation of the NCT technology in third-party applications. In combination with a housing unit, an XTS mover and the AT2100 or AT2102 motor modules, a regulated 24 V DC power supply and synchronous real-time data communication are available on the movers. The basic electronics used already offer a wide range of options for integrating sensors and actuators – digital inputs and outputs, analog inputs and PWM outputs. The basic functionalities can be complemented with application-dependent electronics. All functions can be controlled centrally via TwinCAT, ensuring high usability with short training times.
Product status:
regular delivery
| Product variants | Ordering information |
|---|---|
| AT8200-1000-0100 | NCT electronics, with housing, without mover, basic electronics, 220 g |
| AT8200-2000-0100 | NCT electronics, with housing, without mover, basic electronics, 230 g, suitable for third-party movers |
| AT8300-1100-0100 | NCT electronics, with housing, mounted on AT9014-1070-0550 mover, basic electronics, 900 g |
| AT8300-1200-0100 | NCT electronics, with housing, mounted on AT9014-1070-1550 mover (mover 1), basic electronics, 900 g |
Product information
| Technical data | NCT power transfer |
|---|---|
| Rated output | up to 35 W (depending on the mover position) |
| Peak performance | up to 75 W (depending on the mover position) |
| Output voltage | 24 V DC (regulated) |
| Power transmission | continuously (also across module limits) |
| Technical data | NCT data transfer |
|---|---|
| Communication cycle | 250 µs |
| Communication direction | bidirectional |
| Time response | µs-precise DC synchronization |
| Communication participants | no system limits (individual address assignment of the movers possible) |
| Communication types | cyclic and acyclic |
| Data transfer | continuously (also across module limits) |
| Technical data | Digital input |
|---|---|
| Number of digital inputs | 2 (+2 analog inputs usable as digital inputs) |
| Connection technology | 1-wire |
| Nominal voltage | 24 V DC (-15%/+20%) |
| “0” signal voltage | -3…+5 V |
| “1” signal voltage | 11…30 V |
| Input filter | configurable, standard: 3 ms, min.: 10 µs |
| Counter function | 1 x up/down counter, 1 x up or down counter |
| Counter depth | 32 bit |
| Counter feature | set counter, switch outputs, reset counter |
| Latch function | latch input, 24 V DC |
| Latch resolution | 4 µs resolution, 32 bit time value |
| Technical data | Digital output |
|---|---|
| Number of digital outputs | 4 (+3 PWM output usable as digital output) |
| Connection technology | 1-wire |
| Nominal voltage | 24 V DC (-15%/+20%) |
| Load type | ohmic, inductive, lamp load |
| Switching times | TON: typ. 20 µs, TOFF: 10 µs |
| Short-circuit current | typ. < 2 A |
| Breaking energy | < 150 mJ/channel |
| Technical data | Analog input |
|---|---|
| Number of analog inputs | 2 |
| Technology | single-ended |
| Signal voltage | 0…10 V |
| Internal resistance | 500 kΩ |
| Input filter limit frequency | 2 kHz |
| Resolution | 12 bit |
| Measuring error | < ±0.3% (referred to the measuring range end value) |
| Technical data | Pulse width modulation output |
|---|---|
| Number of outputs | 3 x half bridge with 2 x current measurement or 1 x full and 1 x half bridge with 1 x current measurement each |
| Nominal voltage | 24 V DC (-15%/+20%) |
| Load type | ohmic, inductive, lamp load |
| Max. output current | 2 A |
| Max. switching frequency | 128 kHz |
| Duty factor | 0…100% (TON > 20 ns, TOFF > 200 ns) |
| Technical data | Mechanical data | Connector |
|---|---|
| Connection technology | Cage Clamp® |
| Protection rating | IP20 |
| Connection cross-section | solid wire: 0.08…1.5 mm², stranded wire*: 0.08…1.5 mm², with ferrule: 0.25…1 mm² |
| Connection cross-section AWG | solid wire: AWG28-16, stranded wire*: AWG28-16, with ferrule: AWG28-18 |
| Stripping length | 6…7 mm |
| Technical data | Mechanical data | Housing |
|---|---|
| Length | 118 mm |
| Width | 69 mm |
| Height | 28.5 mm |
| Weight | 230 g (housing incl. electronics) |
| Rated air gap | 0.85 mm |
| Special features | integrated adjustment option for air gap |
| Ordering information | |
|---|---|
| AT8200-2000-0100 | NCT electronics, with housing, without mover, basic electronics, 230 g, suitable for third-party movers |
© Beckhoff Automation 2024 - Terms of Use