IP2040-Bxxx, 8 mm, snap type
on the fieldbus)
3 | GND
4 | Output
2 | +24 V UP IN 6-7
3 | GND
4 | GND
2 | + 24 V UP IN 0-3
3 | GND
4 | GND
IP2040-Bxxx, 8 mm, snap type
The IP2040-Bxxx digital output connects the binary control signals from the automation unit on to the actuators at the process level. The eight outputs handle load currents of up to 2 A each, although the total current is limited to 12 A. The outputs are supplied by three load circuits; for this reason these modules do not relay the supply voltage. The signals are connected via 8 mm snap type connectors.
The outputs are short-circuit proof and protected against inverse connection.
Product status:
service phase | Possibly with other technical features or equipment in case of a service order or repair
Product information
| Technical data digital outputs | IP2040-Bxxx |
|---|---|
| Number of outputs | 8 |
| Output connections | 8 mm, snap type |
| Load type | ohmic, inductive, lamp load |
| Nominal output voltage | 24 V DC (-15%/+20%) |
| Max. output current | 2 A per channel, individually short-circuit proof, total current max. 12 A (channel 0…3: ∑ 4 A, 4+5: ∑ 4 A, 6+7: ∑ 4 A) |
| Short-circuit current | typ. 4 A |
| Auxiliary power current | typ. 50 mA per channel |
| Current consumption from US (without sensor current) | see documentation |
| Power supply connection | feed: 2 x M8 male socket, 4-pin; no downstream connection |
| Bit width in the process image | 8 outputs |
| Electrical isolation | channels/control voltage: no, between the channels: no, control voltage/fieldbus: depends on the bus system |
| Technical data | IP2040-B730 |
|---|---|
| Extension modules | – |
| Digital peripheral signals | according to I/O type |
| Analog peripheral signals | according to I/O type |
| Protocol | RTU/ASCII |
| Configuration possibility | by means of address selection switch or KS2000 |
| Data transfer rates | 150, 300, 600, 1200, 2400, 4800, 9600, 19,200, 38,400 baud |
| Bus interface | 1 x M12 socket, 5-pin, B-coded |
| Data transfer medium | screened, twisted copper cable 2 x 0.25 mm² (RS485) |
| Power supply | control voltage: 24 V DC (-15%/+20%); load voltage: according to I/O type |
| Power supply connection | feed: 2 x M8 male socket, 4-pin; no downstream connection |
| Box supply current | 45 mA + current consumption of sensors, max. 0.5 A |
| Auxiliary power current | according to I/O type |
| Electrical isolation | control voltage/fieldbus: yes, control voltage/inputs or outputs: according to I/O type |
| Distance between stations | max. 1200 m (depending on baud rate) |
| I/O communication types | read/write access, optionally bit oriented or word oriented |
| Weight | approx. 210 g |
| Operating/storage temperature | 0…+55°C/-25…+85°C |
| Vibration/shock resistance | conforms to EN 60068-2-6/EN 60068-2-27 |
| EMC immunity/emission | conforms to EN 61000-6-2/EN 61000-6-4 |
| Protect. rating/installation pos. | IP65/66/67 (conforms to EN 60529)/variable |
| Approvals/markings | CE, UL |
| Housing data | Standard housing |
|---|---|
| Dimensions (W x H x D) | 30 mm x 175 mm x 26.5 mm |
| Material | PA6 (polyamide) |
| Installation | 2 fixing holes 3.5 mm diameter for M3 |
Loading content ...
Loading content ...
Loading content ...
© Beckhoff Automation 2024 - Terms of Use